8-channel Benchmark Amplifier with DSP and optional Dante™
หมายเลขสินค้า : Powersoft, X8 DSP+DANTE
ราคา 647,900.00 บาท
-
ตรวจสอบก่อน! ว่ามีสินค้าหรือไม่
-
*กรุณาโทรเช็คสต็อคสินค้าก่อนสั่ง 061-649-9144
เลือกจำนวน :
เลือกสี : สีดำ
-
ฟรี!
ประกัน 1 ปี
-
ฟรี!
ปรึกษาด้านเทคนิก
แชร์ไปยัง :
8-channel Benchmark Amplifier with DSP and optional Dante™
เพาเวอร์แอมป์ Powersoft X8 เป็นเพาเวอร์แอมป์แบบ 8 ชาแนล พร้อม DSP and Ethernet มีกำลังขับ 1600 Watts per Channel @ 8 Ohms, 3000 Watts per Channel @ 4 Ohms, 5200 Watts per Channel @ 2 Ohms, Channel Routing System, 3 Phase Power Supply, 2U Rack Space
Powersoft X8 innovates and evolves the concept of the amplification platform thanks to the integration of a worldwide compatible three-phase power supply and a fully-featured DSP.
The complete digital audio signal management system based on ARM Cortex A-8 processor and TI C6000 DSP platform heralds new and innovative level of signal processing, providing non-boolean routing and mixing, multi-stage equalization with raised-cosine, IIR and FIR filters, delay up to 2s in input processing and 100ms for time alignment, gain and polarity adjustment, crossover, peak limiters, TruePower™ limiters, and Active DampingControl™.
The power supply permits worldwide AC acceptance and direct connection to any regional power line configuration: it is now suitable for Single Phase, Bi-Phase, or Three Phase operation from 85 VAC up to 440 VAC without the need for manual selection. True Three Phase load balancing is directly achievable by the unit without any complex load assignment in the power distribution system design.
Features :
-
Power supply:
- Suitable for Single-Phase, Two-Phase or Three-Phase operation from 85 VAC up to 440 VAC, with automatic switching and balancing
- Three-phase load balancing directly managed by the unit without the need for complex load assignments in the system design
- Power Factor Correction PFC for low power consumption and compatibility with a wide range of voltages
- Power limiters that eliminate the need for expensive power sequencers
-
Protections:
- Innovative failure protection aimed at keeping the system on its SOA by detecting the power delivered to speakers compared to the power drawn from mains
- Real-time measurement and processing of the output signal in order to obtain the power output: all data are collected and compared with data about the available stored energy and the power available from the mains. This makes the system immune from any misalignment such as overvoltage, overcurrent, short circuit, etc.
- Protection against potentially harmful signals: DC, VHF, and clipping
-
General:
- Flexible routing/mixing provided by the internal 8x8 input/ output matrix, allows the user to mix and route analog and digital I/O.
- 8 input channels with physical analog and digital AES3 connectors and optional 16-in/8-out redundant Dante™ connection provides maximum flexibility.
- Improved reliability thanks to the customizable input backup policy that automatically switches input source in case of a signal failure.
- Complete user interface integrated into ArmoníaPlus.
- WiFi remote monitoring through mobile device.
-
Settings:
- Non-boolean channel routing
- Input signal backup policy aimed to improve reliability against signal fault
- Signal grouping for speaker routing
- Built-in remote management via WiFi
-
Monitoring:
- Hardware monitor available for fast local diagnostics
- Load impedance measurement/display for each channel
- Output power measurements/display for each channel
- Mains voltage and current measurements/display
-
Digital Signal Processing:
- TI C6000 DSP platform architecture
- AD/DA converter: dual 24bit @48 kHz Tandem® architecture, 127 dB dynamic range, per channel
- Input/output independent equalizers per channel providing Raised-cosine, custom FIR, parametric IIR: peaking, hi/lo-shelving, all-pass, band-pass, band-stop, hi/lo-pass
- Crossovers: linear phase (FIR), hybrid (FIR-IIR), Butterworth, Linkwitz-Riley, Bessel: 6 dB/oct to 48 dB/oct (IIR)
- Input delay up to 2s and output delay up to 100ms for time alignment per channel
- Active DampingControl™ for cable compensation
- Power limiter (TruePower™, RMS voltage, RMS current) + Peak Limiter
-
Remote management:
- Control and monitoring through ArmoníaPlus
- Dedicated Web App
General :
-
Output power per channel:
-
Output power per channel:
- 5200 W @ 2 Ω
- 3000 W @ 4 Ω
- 1600 W @ 8 Ω
-
Bridge mode:
- 10400 W @ 4 Ω
- 6000 W @ 8 Ω
-
Output power per channel:
-
Max output voltage / current:
- Max unclipped output voltage @8 Ω: 175 Vpeak
- Current: 130 Apeak
AC Main Power :
- Power supply: Universal, regulated switch mode with PFC (Power Factor Correction)
- Nominal power requirement: 100 – 240 V @ 50/60Hz
- Operating voltage: 90 V – 264 V
-
Power consumption:
- Idle: < 200 W
- Max: < 5000 W
Thermal :
- Operating temperature range: 0° – 45°C (-32° – 113°F)
-
Thermal dissipation:
-
1/8 of max output power @ 8 Ω:
- 115 V: 2117 BTU/h
- 230 V: 1946 BTU/h
-
1/4 of max output power @ 8 Ω:
- 115 V: 3892 BTU/h
- 230 V: 2875 BTU/h
-
1/8 of max output power @ 8 Ω:
เปิด จันทร์ - อาทิตย์
เวลา 9.30 - 18.30 น.
32 ซอยรามคำแหง 24 แยก 30 (หมู่บ้านศิขริน) แขวงหัวหมาก เขตบางกะปิ กรุงเทพมหานคร 10240
บริการให้คำปรึกษา
English Version : 082-623-6663